:orphan:
.. raw:: html
<!--
FIXME: do not limit page width until content uses another representation
format other than tables
-->
<style>.wy-nav-content { max-width: none; !important }</style>
.. dtcompatible:: atmel,at45
.. _dtbinding_atmel_at45:
atmel,at45 (on spi bus)
#######################
Vendor: :ref:`Atmel Corporation <dt_vendor_atmel>`
Description
***********
.. code-block:: none
Atmel AT45 (or compatible) SPI flash
Properties
**********
.. tabs::
.. group-tab:: Node specific properties
Properties not inherited from the base binding file.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``jedec-id``
- ``uint8-array``
- .. code-block:: none
JEDEC ID as manufacturer ID (1 byte) and device ID (2 bytes).
This property is **required**.
* - ``size``
- ``int``
- .. code-block:: none
Flash capacity in bits.
This property is **required**.
* - ``sector-size``
- ``int``
- .. code-block:: none
Flash sector size in bytes.
This property is **required**.
* - ``block-size``
- ``int``
- .. code-block:: none
Flash block size in bytes.
This property is **required**.
* - ``page-size``
- ``int``
- .. code-block:: none
Flash page size in bytes.
This property is **required**.
* - ``use-udpd``
- ``boolean``
- .. code-block:: none
When set, the driver will use the Ultra-Deep Power-Down command instead
of the default Deep Power-Down one to put the chip into low power mode.
From the driver perspective, as it does not rely on the contents of the
SRAM buffers in the chip, the difference between the Deep and Ultra-Deep
Power-Down modes is that the chip consumes far less power in the latter
but needs some more time to enter this mode and to exit from it.
* - ``enter-dpd-delay``
- ``int``
- .. code-block:: none
Time, in nanoseconds, needed by the chip to enter the Deep Power-Down
mode (or Ultra-Deep Power-Down mode when the "use-udpd" property is set)
after the corresponding command is issued.
* - ``exit-dpd-delay``
- ``int``
- .. code-block:: none
Time, in nanoseconds, needed by the chip to exit from the Deep Power-Down
mode (or Ultra-Deep Power-Down mode when the "use-udpd" property is set)
after the corresponding command is issued.
* - ``reset-gpios``
- ``phandle-array``
- .. code-block:: none
The RESET pin of AT45 is active low.
If connected directly the MCU pin should be configured
as active low.
* - ``wp-gpios``
- ``phandle-array``
- .. code-block:: none
The WP pin of AT45 is active low.
If connected directly the MCU pin should be configured
as active low.
* - ``spi-max-frequency``
- ``int``
- .. code-block:: none
Maximum clock frequency of device's SPI interface in Hz
This property is **required**.
* - ``duplex``
- ``int``
- .. code-block:: none
Duplex mode, full or half. By default it's always full duplex thus 0
as this is, by far, the most common mode.
Use the macros not the actual enum value, here is the concordance
list (see dt-bindings/spi/spi.h)
0 SPI_FULL_DUPLEX
2048 SPI_HALF_DUPLEX
Legal values: ``0``, ``2048``
* - ``frame-format``
- ``int``
- .. code-block:: none
Motorola or TI frame format. By default it's always Motorola's,
thus 0 as this is, by far, the most common format.
Use the macros not the actual enum value, here is the concordance
list (see dt-bindings/spi/spi.h)
0 SPI_FRAME_FORMAT_MOTOROLA
32768 SPI_FRAME_FORMAT_TI
Legal values: ``0``, ``32768``
* - ``supply-gpios``
- ``phandle-array``
- .. code-block:: none
GPIO specifier that controls power to the device.
This property should be provided when the device has a dedicated
switch that controls power to the device. The supply state is
entirely the responsibility of the device driver.
Contrast with vin-supply.
* - ``vin-supply``
- ``phandle``
- .. code-block:: none
Reference to the regulator that controls power to the device.
The referenced devicetree node must have a regulator compatible.
This property should be provided when device power is supplied
by a shared regulator. The supply state is dependent on the
request status of all devices fed by the regulator.
Contrast with supply-gpios. If both properties are provided
then the regulator must be requested before the supply GPIOS is
set to an active state, and the supply GPIOS must be set to an
inactive state before releasing the regulator.
.. group-tab:: Deprecated node specific properties
Deprecated properties not inherited from the base binding file.
(None)
.. group-tab:: Base properties
Properties inherited from the base binding file, which defines
common properties that may be set on many nodes. Not all of these
may apply to the "atmel,at45" compatible.
.. list-table::
:widths: 1 1 4
:header-rows: 1
* - Name
- Type
- Details
* - ``reg``
- ``array``
- .. code-block:: none
register space
This property is **required**.
See :ref:`dt-important-props` for more information.
* - ``label``
- ``string``
- .. code-block:: none
Human readable string describing the device (used as device_get_binding() argument)
This property is **required**.
See :ref:`dt-important-props` for more information.
* - ``status``
- ``string``
- .. code-block:: none
indicates the operational status of a device
Legal values: ``'ok'``, ``'okay'``, ``'disabled'``, ``'reserved'``, ``'fail'``, ``'fail-sss'``
See :ref:`dt-important-props` for more information.
* - ``compatible``
- ``string-array``
- .. code-block:: none
compatible strings
This property is **required**.
See :ref:`dt-important-props` for more information.
* - ``reg-names``
- ``string-array``
- .. code-block:: none
name of each register space
* - ``interrupts``
- ``array``
- .. code-block:: none
interrupts for device
See :ref:`dt-important-props` for more information.
* - ``interrupts-extended``
- ``compound``
- .. code-block:: none
extended interrupt specifier for device
* - ``interrupt-names``
- ``string-array``
- .. code-block:: none
name of each interrupt
* - ``interrupt-parent``
- ``phandle``
- .. code-block:: none
phandle to interrupt controller node
* - ``clocks``
- ``phandle-array``
- .. code-block:: none
Clock gate information
* - ``clock-names``
- ``string-array``
- .. code-block:: none
name of each clock
* - ``#address-cells``
- ``int``
- .. code-block:: none
number of address cells in reg property
* - ``#size-cells``
- ``int``
- .. code-block:: none
number of size cells in reg property
* - ``dmas``
- ``phandle-array``
- .. code-block:: none
DMA channels specifiers
* - ``dma-names``
- ``string-array``
- .. code-block:: none
Provided names of DMA channel specifiers
* - ``io-channels``
- ``phandle-array``
- .. code-block:: none
IO channels specifiers
* - ``io-channel-names``
- ``string-array``
- .. code-block:: none
Provided names of IO channel specifiers
* - ``mboxes``
- ``phandle-array``
- .. code-block:: none
mailbox / IPM channels specifiers
* - ``mbox-names``
- ``string-array``
- .. code-block:: none
Provided names of mailbox / IPM channel specifiers
* - ``wakeup-source``
- ``boolean``
- .. code-block:: none
Property to identify that a device can be used as wake up source.
When this property is provided a specific flag is set into the
device that tells the system that the device is capable of
wake up the system.
Wake up capable devices are disabled (interruptions will not wake up
the system) by default but they can be enabled at runtime if necessary.
* - ``power-domain``
- ``phandle``
- .. code-block:: none
Power domain the device belongs to.
The device will be notified when the power domain it belongs to is either
suspended or resumed.